Page 39 Now all the cables have been detached Take the end of the circuit board near the rear of the drive and flip it toward the front, this will reveal one more cord to detach. Page 39 of Page 40 Now the laser assembly is exposed from the bottom of the drive. As well as the top If you wanted to try cleaning the lens and mirror this would be as far as you need to go.
Blast the optics with compressed air attempting to direct the dust away from the lens top and mirror bottom Use a clean Q-tip and lens cleaner to clean the optics, you want to achieve a streak free surface.
Page 41 Push them in the direction of the arrows and they will pop out and the laser assembly can be removed Now you should have a pile of parts that looks something like this Reassembly is the reverse.
Install the laser by pushing the rubber dampeners into their sockets. Connect the circuit board to the white four wire connector on the chassis, lay the circuit board over the chassis and install the four black screws. Page 43 Removing the solder is best accomplished by wiping a clean 15Watt or other low temperature soldering iron across the pads, be very careful!!!
Remove four Phillips 1 screws One of them is under the warranty void if seal damaged sticker Remove the top cover. Page 45 The rail is held in place by a small metal spring loaded tab. The metal is in the shape of a number seven 7 the small leg presses against the plastic and holds the rail from escaping; to remove we need to elevate the metal tab over the plastic so it can slide to the left. Page 46 Getting the tab over the plastic is a two handed operation. I used two small regular precision screw drivers to lift and one to leverage to the side.
In this photo you can see the tab is lifted over the plastic riser, and held in place by a screw driver, the rail can now be lifted up. In this photo the rail has been freed but the front is still attached, pulling the rail about a quarter inch back releases the front. Page 47 Now that the gear and rail has been swapped over to the new laser it is time to re-install the laser and rail. Start by fitting the laser U shaped notch back into the lower rail in this photo.
Next insert the top rail into the standoff at the top right in this picture. Page 48 Using a precision screw driver, depress the tab so it is below the plastic, you may want to also replace the glue that holds the metal in its place.
Reassemble and install in your Xbox! Page 48 of The top and bottom covers come off easily To slide out the tray either use the emergency eject from the front of the drive or flip it over and slide this white thing in the direction of the arrow. Page 50 Removing the DVD tray, two clips need to be depressed on either side of the front of the DVD to allow its removal If you are having tray eject issues the nub on the white thing circled below has most likely jumped out of the trough it fits in on the bottom of the tray, when reassembling the tray be sure this fits back into the trough on the bottom of the tray Removing the laser assembly, remove the two screws where the blue circle is in this photo Page 51 This is a view of the bottom of the drive and you can see the grommet on the right has been removed from its "C" shaped holder.
The grommet on the left still needs to come out! With the laser loose I find this is a good time to remove the circuit board to gain easy access to the ribbon cables. Page 52 Re-assembly - Install the laser assembly back into the chassis, put the shaft of a small screwdriver through the hole in the center of the rubber grommet and push it into place Note the large headed screws on the left in this picture have been installed Lay the PCB on top of the chassis and reconnect two ribbon cables Page 52 of Page 53 The PCB is held in place by two back plastic clips circled below, press the board into place Flip the drive into the upright position.
On the top, install the ribbon cable that attaches to the laser. Page 55 For the purposes of this tutorial I have removed the ribbon cables to get better shots of the laser, this is not necessary for adjusting the pot Looking at the Pot we see 3 contacts.
Position the drive so the single contact is on your left, the one to measure from on the right is the lower one. Page 56 Touch points 1 and 3 with the probes, you use red or black with either it makes no difference. Get an initial reading, it should be over and not fluctuate. Scrape away the epoxy on the screw, not always an easy task and probably the most likely chance to irreparably damage your DVD.
The bigger paperclips work best. Straighten it out as below. You will find a hole on all Xbox consoles at Arrow 1. Page 58 Once it is out far enough the tray can be pulled out easily, never force it Page 58 of Here is what they mean. Disclaimer: This information is a believed to be correct, should be as close as it gets; If you have an Xbox with bad Hard Drive the process to swap gets a bit more complicated and there is no possibility of doing this without installing a modchip.
Page 63 That's all. You can now recover those memories, once thought lost, from your locked hard drive. Remember, when booting your XBOX only the locked hard drive you were trying to recover will boot.
Any other hard drive will need to be unlocked to boot up. Page 64 Xbox apps to easily unlock a drive with 1 button click. ConfigMagic can unlock harddrives, but also newer versions of EvolutionX dashboards and also all 4th generation modchip OS'. Page 66 Extracting the HD password from an Xbox hard drive The Xbox harddrive uses a fairly old but relatively unused set of security commands to prevent easy access to it's built in drive.
You will see if you are watching the DIOR line that the Xbox is polling that register waiting for the bit to clear. When it does the Xbox will begin transferring the data bytes to the drive.
Page 68 DIOW line changes, but should be able to see all of the actual data bus changes. If you decide to try this, verify it works on some other drive before using your Xbox drive, as I have no idea what kinds of problems might come up if it fails.
Page 69 Error Code When Error Code 21 comes up power off the Xbox, unplug the Xbox 1's hard drive and put it back into Xbox 1. Reconnect all the cable to Xbox 1's hard drive and boot it. It should boot fine. Now power off and put both Xboxes back together. Page 70 More importantly you are able to use this to install Linux on an Xbox, through the use of an altered bios you will be able to link your Xbox through a network connection and upload files as necessary.
Page 71 Notice how the solder around R71R covers two traces and the splash links a third. If you look closely you will see similar situations on several of the other soldier points. If you have never used a soldering iron on electronics before, an Xbox motherboard is a bad place to learn.
Try on an old board first! Error 7 - kernel This is a hard drive error. Page 72 So I placed a regular hd drive in it, and it gave error I was expecting 05, but since the drive did not contain any Xbox partitions it seems logical. So I put in a game cd and then I did get error 5. Also try switching to another video mode by changing the cable. I currently have an Xbox that displays this error when connected to the standard composite video cable but boots fine when connected to a RF adapter cord.
Page 74 LED light turns steady green just like it would look if it were working fine. This fix works only on 1. Prior to fixing the traces the box would attempt to boot three times and then go to the flashing red and green led. The orange line in the upper center is where a conductive pen was used to attempt to re-connect a lifted trace. Page 77 Using a Watt soldering iron tin the points and the ends of the wires with solder.
All you need to do is make contact, don't focus on getting a large amount of solder, a wire that stays in place is all you need there will never be any stress on the wires and it is not a race, take your time. Use an X-Acto knife to scrape off any green board material away from the solder points.
By far the easiest fix, may as well spend the 30 minutes it takes to clean them up. Nothing worse than dieing because of a missed shot or jump! So for those of you that need a little encouragement here we go. Page 79 You can now safely remove all the buttons and rubber cups they sit in. I gave all the buttons and D-pad a nice bath in warm soapy water.
If the board has become drenched with your favorite soda or whatever use some mild soapy water on a rag to clean it up, stay away from window cleaner and other harsh cleaners. Page 80 Alright, now we are ready to take the bottom and lower it on top of the buttons and top cover. Put the screws back where they were and you are done! Fix your broken Xbox controller cord. Cut away the damaged portion of cord and strip back the insulation a couple of inches. Or one you suspect has a bad cord.
Page 83 Once you have thoroughly cleaned the motherboard using compressed air, remove the backing from the heat sink and place it squarely on top of the chip, continue to put firm within reason pressure on it for two minutes.
Now to take the last step to improve cooling as much as possible we will replace the standard power source for the fan with a higher voltage one to make the fan run faster. I was in the process of repairing traces and booted it many times without issue then suddenly without warning the box would suddenly not respond to power or eject buttons. Insert it inline to the cord going to the hard drive and your all set! Whenever the Xbox is on so is the fan just as it is with the motherboard power header.
This is also known as the 12V fan mod. If you want to just swap out the broken component and get up and running here is a list of every error and what is suggested to replace.
Page Dvd Drive Failure 3. Fix existing DVD drive. If your original Xbox DVD drive is dead, completely, no life at all, this may help you. There are 2 small fuses on the drive PCB on the opposite side to the BA chips look elsewhere to see how to get to them they are brown rectangles with the markings "MP" Print page 1 Print document 87 pages. Rename the bookmark. Show Other Languages. Author: Miroslav Djuric and 10 other contributors.
Create a Guide I Have This. Do you know which kind you have? Featured Guides. Front Panel Board. Hard Drive. Heat Sink. Optical Drive. Upper Case. Wi-Fi Board. Wifi Card. Teardowns Xbox One Teardown. Xbox One Won't Turn On. Support Questions Ask a Question. TR9 Torx Security Schraubendreher. TR10 Torx Security Schraubendreher. Metal Spudger. Essential Electronics Toolkit.
Kreuzschlitzschraubendreher 0. Kreuzschlitzschraubendreher 1. Background and Identification.
0コメント