Panel Planner equipment and panels can be updated locally or over the internet keeping you up-to-date, with the most recent instruments in the market, ready for you to use. The software is multi-platform, based in a technology called Java, and can run either on Macintosh or Windows.
Version 4. Panel Planner J software comes with a day money back guarantee. Read more details. Panel Planner Specs. To overcome this parallax viewing error, and to make them easier to read, these instruments can be installed in a small cocked panel section.
However, this complicates the construction of the panel and you might not even like the effect. Building The Panel It is a good idea to use nothing but non-magnetic materials for your instrument panel. This will afford you more options for locating your compass.
The majority of instrument panels, and panel sub-sections, are normally cut out of a fairly thick sheet of aluminum. A large, one-piece, basic panel, for example, may be cut from a hunk of. This thickness will provide enough rigidity for even a heavily instrumented installation.
It is a good idea, too, to make the basic support instrument panel completely removable. If you have a fuselage fuel tank in the nose end, a removable instrument panel may be essential should the fuel tank ever have to be pulled out for any reason. This means the panel should perhaps be attached to the basic fuselage structure with nut plates. A suggested minimum thickness for a large wide panel, however, would appear to be.
Heavier panels made of. Some builders like the appearance of a wood panel and make theirs of plywood or overlay the aluminum panel with a veneer or textured synthetic sheet.
Such a thick panel, however, introduces some problems when it comes time to install the instruments. For one thing, longer screws will be necessary. In addition, the faces of the instruments will be recessed by the thickness of the plywood. You might not like that effect. However, you could bevel the instrument panel holes and paint the beveled portions flat black.
Naturally, it all depends on the effect you would like to achieve. You only have yourself to please. Panels are best cut out on a bandsaw and smooth trimmed with a disc sander or a belt sander. A saber saw also works well although more finishing work will have to be done.
In the absence of such luxurious equipment you can do an adequate job with a hacksaw, a large bastard cut file and sandpaper. The sizes are not interchangeable so know which instruments take which size holes and where. This tool has an infinite range of hole size adjustments within its capacity, and does a fine job. It can be dangerous to use if you allow your hands to get in the way of the sweeping bar and cutter. Always clamp your work to the drill press.
Use a rather slow speed. The larger the hole, the slower the drill press speed should be. About rpm is a good average cutter speed for aluminum. This tool should not be used in a handheld drill as it is difficult to control without jamming. After you have adjusted the cutter to the size hole you want, make a test cut on some scrap. You want the instrument to slip into the finished hole easily.
Pilotshop assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.
Panel Builder does have a template for Socata TB If you have the dimensions for a panel you can submit them to the manufacture One Mile Up and they will add it for free. The manufacture is very good at updating there software with new units and panels. Many customers have bought the software and had there panel uploaded. You can contact the manufacture at onemileup. Yes, per the manufacture it will work on Windows 7 and in the manual gives instruction on how to install.
Many customers have bought the software and had there blank panel uploaded. No, however upon purchase the manufacturer will add the Bearhawk Patrol if you send in a drawing.
Yes, the Eurocopter AS does have a template in the panel planner. The B and B3 models can be added at no additional charge if you provide the manufacturer with the specs. This is a download. After purchase has been processed you will receive an email with instructions on how to download and will also include an activation key.
Quick Shop. Length Quantity. Your Cart. Quantity Delete. Add Options.
0コメント